Week 5 Update

 First and foremost, I have been gradually cleaning the typewriter, so I'm hoping the smell gets better and better as time goes on. I also ditched the suitcase that it had probably been sitting in for 40 years, so I think that'll help too. 

Here's my cart on digikey that I made after watching the video. I'm holding off on adding switches until I can get some better measurements of distance between each bar - that will help determine if it's feasible to do a switch per key bar or revert to something else. 


I'm also looking ahead to see what resources I'll need to build an actual circuit board. I found this youtube playlist, but can't tell if it's worth my time or not yet: https://www.youtube.com/watch?v=la5BafeXsUI . There may be something better. 

In class on Thursday, I started thinking about how to build the mail slot and what I might need for that, but I want to try to limit myself to getting the typewriter to work before I move forward. I think its a really interesting challenge and I don't want to get ahead of myself if there are missing pieces along the way. I may go ahead and order some of the bendable wood we looked at just to experiment with it, but other than that, I need to focus on one thing at a time or else this will never get done. 


Comments

Post a Comment

Popular posts from this blog

Week 6 Update

Image
Lots of Project Updates!  Shopping is (sort of) complete. I bought both types of shift registers x6, the jumper wire kit, and five switches. Why only 5? Well, I ran into an issue when trying to measure the distance between each key bar on the typewriter... There is a gear under there that puts some of the bars at an angle, and even aside from that weird gap, there is no consistent measurement for the ones that are parallel to each other. It's hard to tell in the image, but most of them are slightly different distances apart.  I hope I'm correct in assuming that this wont be a huge issue when making a custom circuit board, but when I test on the breadboard, it is going to be pretty hard to align a switch for each one of those bars. And with the switches being over a dollar each, I didn't want to spend ~$50 before knowing that they would work out, so I decided to only order 5 so that I can get a feel for the size and placement of the switches without fully committing. I know ...
Read more

Week 4 Update

Image
 The long awaited lab update😲😲😲 Lab 4:  I had to fumble through the beginning because I still have not been able to go to the lab and use the multimeter (happening Monday!!) But I watched the full lab 2 video just so I could understand the voltage divider better, and the potentiometer worked perfectly. Adding the LED was a struggle at first, but it was just wiring errors on my part, and eventually I was able to control the brightness with the potentiometer. Here is the completed setup:  I'm still struggling to comprehend why we divided by 4 to define the brightness value from reading. I assume it has to do with units of measurement, especially since I used 10k resistors for part 1 and switched to 220 for the LED. Need clarification on this. Thanks to our talk in class about PWM, though, I can see how pins 9 and 13 differ. Overall, I'm getting more confident with circuitry, and I think this will make more sense after I connect the dots with lab 2.  Lab 5: Lab 5 wen...
Read more

Update and Code Dump

 I spent a little bit of time today trying new versions of the shapes on fusion / illustrator and still haven't gotten it quite right. Tomorrow, I'm going to spend as long as it takes until its correct. Woohoo!  It has been really frustrating so I took a break from measuring over the course of the week and researched some code that I will need to move forward once I have the correct circuit board. Most of it is a collaboration of chatgpt and my edits, and it will require more edits once I have all the parts and it is working for real, but I'm going to dump my drafts here.  This is the hypothetical sequence to turn the connection signals into the actual characters with 5 shift registers. I know I found some code online for this before, but that was designed for switches and this involves pull-up resistors so it should be debounced:  // Pin configuration for the shift registers const int latchPin = 9; // Latch pin connected to Arduino pin 9 const int clockPin = 10; //...
Read more